Double-sided circuit board is the middle layer of medium, and both sides are wiring layers. A multi-layer circuit board is a multi-layer wiring layer, and there is a dielectric layer between every two layers, and the dielectric layer can be made very thin. Multilayer circuit boards have at least three conductive layers, two of which are on the outer surface, and the remaining layer is integrated into the insulating board. The electrical connection between them is usually achieved through plated through holes on the cross section of the circuit board. In a series of production processes of PCB boards, there are many matching points. If you are not careful, the board will have defects, which will affect your whole body, and the quality of PCB boards will be endless. Therefore, after the circuit board is manufactured and formed, the inspection test becomes an indispensable link. Let me share with you the faults of PCB circuit boards and their solutions.

　　One, what delamination often occurs in multilayer circuit boards in use

　　1. Supplier material or process problem;

　　2. Improper packaging or storage, damp;

　　3. Poor design material selection and copper surface distribution;

　　4. The storage time is too long, and the storage period is exceeded, and the PCB board is damp.

　　Responsive measures: choose the packaging, use constant temperature and humidity equipment for storage. Do a good job of PCB factory reliability test, such as: thermal stress test test in PCB reliability test, the responsible supplier is to use more than 5 times of non-layering as the standard, and it will be confirmed during the sample stage and each cycle of mass production. The general circuit board manufacturers may only require two times, and only confirm once a few months. The IR test of simulated placement can also prevent the outflow of defective products more, which is a must for an excellent PCB factory. In addition, the Tg of the PCB board should be selected above 145°C, so that it is safer.

　　Reliability testing equipment: constant temperature and humidity box, stress screening type thermal shock test box, PCB reliability testing equipment.

　　PCB multilayer circuit board production

　　2. The solderability of the multilayer circuit board is poor

　　Reasons: too long storage time, resulting in moisture absorption, contamination and oxidation of the layout, abnormal black nickel, solder resist SCUM (shadow), and solder resist PAD.

　　Solution measures: Strictly pay attention to the quality control plan of the PCB factory and the standards for maintenance when purchasing. For example, black nickel, you need to see whether the circuit board manufacturer has chemical gold out, whether the chemical gold wire solution concentration is stable, whether the analysis frequency is sufficient, whether there is a regular gold stripping test and phosphorus content test for testing, and whether the internal solderability test is Have good execution and so on.

　　Three, multilayer circuit board impedance is poor

　　Reason: The impedance difference between PCB batches is relatively large.

　　Responsive measures: The circuit board manufacturer is required to attach batch test reports and impedance strips when delivering goods, and if necessary, provide comparative data of the inner wire diameter and the edge wire diameter of the board.

　　Four, multi-layer circuit board bending and warping

　　Reasons: unreasonable material selection by the supplier, poor control of heavy industry, improper storage, abnormal operation line, obvious differences in copper area of each layer, and insufficiently made broken holes.

　　Countermeasures: pressurize the thin board with wood pulp board before packaging and shipping to avoid deformation in the future. If necessary, add a fixture to the patch to prevent the device from bending the board excessively. The PCB needs to simulate the mounting IR conditions for testing before packaging, so as to avoid the undesirable phenomenon of plate bending after the furnace.

　　5. Solder-proof blistering/falling off

　　Reason: There is a difference in the selection of solder mask, the solder mask process of multilayer circuit boards is abnormal, caused by heavy industry or excessively high patch temperature.

　　Responsive measures: PCB suppliers should formulate reliability test requirements for multilayer circuit boards and control them in different production processes.

　　Six, the Cavani effect

　　Reason: In the process of OSP and Dajinmen, electrons will dissolve into copper ions, resulting in a potential difference between gold and copper.

　　Countermeasures: PCB manufacturers are required to pay close attention to the control of the potential difference between gold and copper in the production process.

Read recommendations:

Aluminum substrate (double-sided)

High frequency PCB

SMT stickers

Mobile phone board

Common PCB component packaging.Automotive lighting PCB