Talking about how to deal with the circuit board soldering off_

Automotive lighting PCB sales,BGA circuit board Merchant,Circuit board patch Vendor-Shenzhen VEC Technology Co., Ltd.

Tel: +86-755-29662580

Email: sales@victoriapcb.com

中

current position: Home 》 News 》 Industry News

Talking about how to deal with the circuit board soldering off

source:Industry News release time:2021-09-13 Article author:sznbone Popular:pcb

　　Talking about how to deal with the circuit board soldering off

　　I saw that some friends would ask what should I do if the soldering pads of the circuit board are soldered off, and how to deal with it? Shenzhen PCB proofing manufacturers also encountered the same situation when they were producing circuit boards.

　　When the circuit board is soldered, the pad falls off mostly because the soldering time is too long or the temperature is too high due to repeated soldering. The copper pad of the circuit board will fall off after repeated expansion. Pay more attention to this to prevent more falling off when soldering.

　　The circuit board cuts off the peeled pads with a knife and cuts them to the place where they are not peeled off to prevent the circuit from expanding along the peeling place. If your component pins are long enough, you can scrape off the insulating varnish at the circuit joints after cutting, and finish it. Solder the far-sighted pins here. If your PCB circuit board component pins are not long enough, you can use a piece of thin wire to solder through the pad hole and then solder to the component pins, and solder the other end to the soldering Use hot melt glue to fix the joints of the disk to prevent re-opening and falling off

Talking about how to deal with the circuit board soldering off(图1)

　　If the pad of your circuit board falls off very seriously, the above method is not suitable. You can also choose the flying lead method. Solder one end of the wire to the pin of the desoldered component, and the other end is soldered to the pad that is connected to the desoldered pad. Any solder joints. There is another way, bridging. If there are components on the same circuit around the soldered pad component pins, you can directly solder the component pins to the component pins and discard the original pads. Of course, when soldering, you must see clearly that you cannot solder the string to prevent burnout of the components.

　　Well, today, the editor of Shenzhen PCB Proofing Manufacturer will talk about this first. The above is to share this information with you. I hope you can learn more about the knowledge of circuit boards. Friends who need to purchase circuit boards, please contact me. Oh!

Read recommendations:

Six-layer Immersion Gold Board (BGA)

Silver oil perforated plate (double-sided)

Mobile phone board

Six-layer Immersion Gold Board (BGA)

Previous:How to deal with circuit board exhaust gas Back to list Next:Why the circuit board after soldering must be cleaned

Popular recommended products

Six-layer Immersion Gold Board (BGA)

Computer card board (four layers)

Six-layer Immersion Gold Board (BGA)

Silver oil perforated plate (double-sided)

Single copper base PCB

Laminate copper-based PCB after 4L (sample)

Network communication board (sixth floor)

Single-sided double-layer AL base PCB

Six-layer Immersion Gold Board (BGA)

High frequency PCB

Aluminum substrate (double-sided)

Six-layer Immersion Gold Board (BGA)

Six-layer Immersion Gold Board (BGA)

Six-layer Immersion Gold Board (BGA)

Six-layer Immersion Gold Board (BGA)

High frequency PCB

Six-layer Immersion Gold Board (BGA)

High frequency PCB

Six-layer Immersion Gold Board (BGA)

Display board (six layers)

Six-layer Immersion Gold Board (BGA)

High frequency PCB

Mobile phone template (six layers)

Six-layer Immersion Gold Board (BGA)

Six-layer Immersion Gold Board (BGA)

Six-layer Immersion Gold Board (BGA)

Mobile phone board

DIP plugin

Mobile phone board

Six-layer Immersion Gold Board (BGA)

SMT stickers

DIP plugin

Six-layer Immersion Gold Board (BGA)

SMT stickers

Related Information

Composition of PCB

What is the difference between PCB and PCBA

PCB usage tips

Why do the circuit boards are green

How to clean the aluminum substrate?

Maintenance of Chemical Copper Plating Solution on PCB Board

single-sided PCB board and double-sided PCB board

PCB board production process flow

PCB CTI level

Via technology in circuit board factory.Automotive Electronics PCB

The role of FPC flexible circuit board solder mask

Detailed explanation of PCB board sampling production process

pcb v-cut depth standard

Multilayer Printed Circuit Board.What is the eq of PCB

The relationship between PCB safety distance and voltage

SMT surface mount processing.Hybrid circuit board PCB

PCB enterprises should pay attention to SMT matters.Electronic components PCB

PCB - the core building block of electronic products.Automotive Electronics PCB

PCB - the bridge and link of the electronic world

How to define high-frequency and high-precision circuit boards.Industrial Electronics PCB

USB PCB interface layout and wiring requirements

Electrolytic capacitor PCB.Steps for using PCB pins

Automotive ElectronicWhat aspects should be considered when processing and manufacturing PCB boards?

Electrolytic capaciWhat is the difference between a gold-plated circuit board and a gold-plated one?

When grinding PCB boards, attention should be paid to.Oscillator (belonging to crystal) PCB

Industrial Electronics PCB!What precautions should be taken when copying and grinding PCB boards

Do you know who is more suitable for LED direct display, regarding the difference between PCB board

Aluminum electrolytic capacitor PCB.What are the standards for selecting PCB boards

Surface Mount Technology (SMT) Phase PCB

Oscillator (belonging to crystal) PCB.The main functions of PCB board