1. Reasons for raw materials of PCB circuit board laminates:

　　1. It is mentioned above that ordinary electrolytic copper foils are galvanized or copper-plated wool foil products. If the wool foil is produced with an abnormal peak value, or when galvanized/copper-plated, the coating dendrites are not good, causing the copper foil itself. The peel strength is not enough. After the poor foil pressed sheet is made into a PCB circuit board, when it is inserted in an electronic factory, the copper wire will fall off under the impact of external force. This kind of poor copper rejection will not cause obvious side etching after peeling the copper wire to see that the rough surface of the copper foil (that is, the surface in contact with the substrate), but the peeling strength of the copper foil on the whole surface will be very poor.

　　2. Poor adaptability of copper foil and resin: Some laminates with special properties, such as HTg sheets, are currently used because of different resin systems. The curing agent used is generally PN resin, and the resin molecular chain structure is simple. When curing The degree of crosslinking is low, and it is necessary to use copper foil with special peaks to match it. When producing laminates, the use of copper foil does not match the resin system, resulting in insufficient peel strength of the metal-clad sheet metal foil, and poor copper wire falling off when inserting.

　　2. Reasons for the PCB circuit board laminate process:

　　Under normal circumstances, as long as the laminate is hot-pressed for more than 30 minutes in the high temperature section, the copper foil and the prepreg are basically completely combined, so the pressing generally does not affect the bonding force between the copper foil and the substrate in the laminate. However, in the process of stacking and stacking laminates, if PP is contaminated, or the rough surface of copper foil is damaged, it will also lead to insufficient bonding force between copper foil and substrate after lamination, resulting in positioning (only for large boards and language) or sporadic copper wires fall off, but there is no abnormality in the peeling strength of copper foil near the off-wire.

　　, circuit board factory process factors:

　　1. The PCB circuit design is unreasonable. Designing too thin circuits with thick copper foil will also cause excessive circuit etching and copper rejection.

　　2. A local collision occurs in the production process of the PCB factory, and the copper wire is separated from the base material by external mechanical force. This defect is manifested as poor positioning or orientation, and there will be obvious twists in the dropped copper wire, or scratches/impact marks in the same direction. Peel off the bad copper wire and look at the rough surface of the copper foil. It can be seen that the color of the rough surface of the copper foil is normal, there will be no bad side corrosion, and the peeling strength of the copper foil is normal.

　　3. The copper foil is over-etched. The electrolytic copper foils used in the market are generally single-sided galvanized (commonly known as ashing foil) and single-sided copper-plated (commonly known as reddish foil). Foils, red foils and ashing foils below 18um have basically not experienced batch copper rejection.

　　When the customer's circuit is designed to pass the etching line, if the copper foil specification is changed but the etching parameters remain unchanged, the copper foil will stay in the etching solution for too long. Because zinc is an active metal, when the copper wire on the PCB is immersed in the etching solution for a long time, it will inevitably lead to excessive side etching of the circuit, causing the backing zinc layer of some thin circuits to be completely reacted and separated from the substrate. That is, the copper wire falls off.

　　Another situation is that there is no problem with the etching parameters of the PCB circuit board, but the water washing and drying after etching are not good, causing the copper wire to be surrounded by the etching solution left on the PCB surface. Too much and throw copper. This situation is generally concentrated on thin lines, or during humid weather, similar defects will appear on the entire PCB. Strip the copper wire to see that the color of the contact surface with the base layer (the so-called roughened surface) has changed. The color of the copper foil is different from that of the normal copper foil. The original copper color of the bottom layer is seen, and the peeling strength of the copper foil at the thick circuit is also normal.

Read recommendations:

Silver oil perforated plate (double-sided)

High frequency PCB

Mobile phone board

Six-layer Immersion Gold Board (BGA)

The PCB board industry continues to prosper, and 5G is expected to bring a market of more than 60 bi