High-precision PCB circuit board refers to the use of fine line width/spacing, tiny holes, narrow ring width (or no ring width) and buried, blind holes and other technologies to achieve high density. And high precision means that the result of "thin, small, narrow, thin" will inevitably bring high precision requirements. Take the line width as an example: 0.20mm line width, according to the regulations, 0.16 ~ 0.24mm is qualified, and the error is ( 0.20±0.04)mm; and the line width of 0.10mm, the error is (0.10±0.02)mm, obviously the latter’s accuracy is doubled, and so on is not difficult to understand, so the high-precision requirements will not be discussed separately . But it is a prominent problem in production technology.

　　(1) In the future, the high and fine line width/spacing of fine wire technology will be from 0.20mm-0.13mm-0.08mm-0.005mm to meet the requirements of SMT and Multichip Package (MCP). Therefore, the following techniques are required.

　　①Using thin or ultra-thin copper foil (<18um) substrate and fine surface treatment technology.

　　②PCB circuit board adopts thinner dry film and wet film process, thin and good quality dry film can reduce line width distortion and defects. Wet lamination can fill small air gaps, increase interfacial adhesion, and improve wire integrity and accuracy.

　　③Electrodeposited photoresist film (Electro-deposited Photoresist, ED) is used. Its thickness can be controlled in the range of 5~30/um, which can produce more perfect fine wires. It is especially suitable for narrow ring width, no ring width and full-board electroplating. At present, there are more than ten ED production lines in the world.

　　④Using parallel light exposure technology. Since parallel light exposure can overcome the influence of line width variation caused by the "point" light source's oblique light in all directions, fine wires with precise line width dimensions and clean edges can be obtained. However, parallel exposure equipment is expensive, requires high investment, and requires work in a high-cleanliness environment.

　　⑤ Adopt automatic optical inspection technology (Automatic Optic Inspection, AOI). This technology has become an essential means of detection in the production of fine wires, and is being rapidly promoted, applied and developed. For example, AT&T Company has 11 AoIs, and ｝tadco Company has 21 AoIs specially used to detect the graphics of the inner layer.

　　(2) The functional holes of the printed board for surface mounting of micro-hole technology mainly play the role of electrical interconnection, which makes the application of micro-hole technology more important. Using conventional drill bit materials and CNC drilling machines to produce tiny holes has many failures and high costs. Therefore, the densification of printed boards is mostly due to the densification of wires and pads. Although great achievements have been made, its potential is limited. To further improve the densification (such as wires less than 0.08mm), the cost has risen sharply. , thus turning to the use of micropores to improve densification.

　　PCB circuit board (high precision impedance circuit board)

　　In recent years, breakthroughs have been made in CNC drilling machine and micro-drill technology, so micro-hole technology has developed rapidly. This is the main prominent feature in the production process of the current PCB circuit board factory. In the future, the technology of forming tiny holes will mainly rely on advanced CNC drilling machines and excellent tiny heads, while the holes formed by laser technology are still inferior to those formed by CNC drilling machines from the point of view of cost and hole quality.

　　①CNC drilling machine At present, the technology of CNC drilling machine has made new breakthroughs and progress. And formed a new generation of CNC drilling machine characterized by drilling tiny holes. The efficiency of drilling small holes (less than 0.50mm) by the micro-hole drilling machine is 1 times higher than that of the conventional CNC drilling machine, with fewer failures, and the rotation speed is 11-15r/min; it can drill 0.1-0.2mm micro-holes, and the cobalt content is higher. The high-quality small drill bit can drill three boards (1.6mm/piece) on top of each other. When the drill bit is broken, it can automatically stop and report the position, automatically replace the drill bit and check the diameter (the tool magazine can hold as many as hundreds), and can automatically control the constant distance between the drill tip and the cover plate and the drilling depth, so blind holes can be drilled. , and will not damage the countertop. The CNC drilling machine table adopts air cushion and magnetic floating type, which moves faster, lighter and more precise, and will not scratch the table. Such drilling machines are in short supply at present, such as the Mega4600 from Prurite in Italy, the ExcelIon2000 series in the United States, and new-generation products from Switzerland and Germany.

　　②There are indeed many problems with laser drilling conventional CNC drilling machines and drills to drill tiny holes. It has hindered the progress of micro hole technology, so laser hole etching has been paid attention, research and application. But there is a fatal disadvantage, that is, the formation of horn holes, which is aggravated as the thickness of the PCB board increases. Coupled with the pollution of high temperature ablation (especially PCB multilayer circuit boards), the life and maintenance of the light source, the repeatability of the etching hole and the cost, etc., the promotion and application of micro holes in the production of printed boards has been limited. However, laser etching is still used in thin and high-density microplates, especially in MCM-L's high-density interconnect (HDI) technology, such as polyester film etching and metal deposition (sputtering) in M.C.Ms. technology) combined with high-density interconnection. The formation of buried vias in high-density interconnect multilayer circuit boards with buried and blind via structures can also be applied. However, due to the development and technological breakthroughs of CNC drilling machines and tiny drill bits, they have been rapidly promoted and applied. Thus the laser drilled holes on the surface

　　The application in the mounted circuit board cannot form a dominant position. But it still has a place in a certain field.

　　③Buried, blind, through-hole technology Buried, blind, through-hole technology is also an important way to improve the high density of printed circuits. Generally, buried and blind vias are tiny holes. In addition to increasing the number of wirings on the board, buried and blind vias are interconnected between the "nearest" inner layers, which greatly reduces the number of through holes formed, and the setting of the isolation disc will also greatly reduce the number of vias. Reduced, thereby increasing the number of effective wiring and interlayer interconnections in the board, and improving the high density of interconnections. Therefore, the multi-layer board with the combination of buried, blind and through-hole is at least 3 times higher than the conventional full-through-hole board structure under the same size and number of layers. The size of the printed board combined with through holes will be greatly reduced or the number of layers will be significantly reduced. Therefore, in high-density surface mount printed boards, buried and blind via technologies are increasingly used, not only in surface mount printed boards in large computers, communication equipment, etc., but also in civil and industrial applications. It has also been widely used in the field of , and even in some thin boards, such as various PCMCIA, Smard, IC cards and other thin circuit boards with more than six layers.

　　The printed circuit board (PCB circuit board) with buried and blind hole structure is generally completed by the "sub-board" production method, which means that it can only be completed after many times of pressing, drilling, hole plating, etc., so the precision Positioning is very important.

Read recommendations:

Laminate copper-based PCB after 4L (sample)

Computer card board (four layers)

Six-layer Immersion Gold Board (BGA)

SMT stickers

Relay PCB factory